Examples of available add-on testboards
(Additional options and testboards are also available.) Continuity test:
1) Detects open lines, short circuits and miswired cables.
2) Pass/fail test with a 'known good' sample.
3) Locate intermittent connections and identify their position in the cable.
Measurement of Resistance:
1) With the M3U tester, set two resistance thresholds, one for good connections down to 0.3 Ω, and one for isolation up to 10 MΩ.
2) Measure embedded resistors and resistor networks, check the orientation of diodes, and measure diode forward voltage.
High-Voltage test system module HVX for the M3U base system. For tests with up to 1500 VDC or 1000 VAC. 128 test points, expandable to 512. Measures resistance 0,1 Ω to 1 GΩ, tests dielectric breakdown and isolation resistance.
Also optionally an expansion module for 4-wire measurement is available.
Testing system for cable and harness assemblies (expandable up to 2560 test points)
- CableEye system for Continuity test and Measurement of resistance with 152 test points -
With the CableEye cable testers and harness testers, find defective or miswired cables instantly before they damage equipment or waste valuable technician time. CableEye cable testers and harness testers have a unique, patented graphic wiring display to visually pinpoint problems when wiring errors are detected, and offer one-second pass/fail testing for production environments. Quickly locate intermittent connections and identify their position in the cable.
Test Points Available: 64/128/152 switch selectable - expandable up to max. 2560
Resistance Measurement: 1% from 100 Ω to 1 MΩ (lesser accuracy over full range)
Diode Measurement: Orientation and Forward Voltage
Test Voltage: 10 V
Maximum Test Current: 1 mA
Insulation Resistance Measurement Range: 10 MΩ Max. at 10 V
Calibration: Recommended Yearly
Test Point Connectors: 64-pin dual-row headers, 0.1” (2.54 mm) centers - two per 128-point module
Remote Control Socket: MiniDIN8 connector for footswitch, external control panel
Probe Socket: yes - incl. test probe - accessory port also useable with minihook cables
Power Requirement: 18 VDC at 500 mA (max), 9 W, from wall module
Computer Requirements: Windows XP®/Vista®/7®/8®
M2U FULL (up to 1024 TP)
Examples of available add-on testboards
(Additional options and testboards are also available.)
Continuity test:
1) Detects open lines, short circuits and miswired cables.
2) Pass/fail test with a 'known good' sample.
3) Locate intermittent connections and identify their position in the cable.
Testing system for cable and harness assemblies (expandable up to 1024 test points) - CableEye system with 152 test points -
With the CableEye cable testers and harness testers, find defective or miswired cables instantly before they damage equipment or waste valuable technician time. CableEye cable testers and harness testers have a unique, patented graphic wiring display to visually pinpoint problems when wiring errors are detected, and offer one-second pass/fail testing for production environments. Quickly locate intermittent connections and identify their position in the cable.
Test Points Available: 64/128/152 switch selectable - expandable up to max. 1024
Test Time: 0.2 Sec
USB-Interface: 1.1 - fast
Resistance Thresholds: 46 kΩ - fixed
Resistance Measurement: no
Diode Measurement: Orientation Only
Test Voltage: 5 V
Maximum Test Current: 0.3 mA
Calibration: Not required
Test Point Connectors: 64-pin dual-row headers, 0.1” (2.54 mm) centers - two per 128-point module
Remote Control Socket: MiniDIN8 connector for footswitch, external control panel
Probe Socket: yes - incl. test probe - accessory port also useable with minihook cables
Power Requirement: 9v DC at 300 ma (max), 3w, from wall module
Computer Requirements: Windows XP®/Vista®/7®/8®
M2U BASIC (up to 128 TP)
Examples of available add-on testboards
(Additional options and testboards are also available.)
Continuity test:
1) Detects open lines, short circuits and miswired cables.
2) Pass/fail test with a 'known good' sample.
3) Locate intermittent connections and identify their position in the cable.
Testing system for cable and harness assemblies (not expandable) - CableEye basic system with max. 128 test points -
With the CableEye cable testers and harness testers, find defective or miswired cables instantly before they damage equipment or waste valuable technician time. CableEye cable testers and harness testers have a unique, patented graphic wiring display to visually pinpoint problems when wiring errors are detected, and offer one-second pass/fail testing for production environments. Quickly locate intermittent connections and identify their position in the cable.
Test Points Available: 128 - no expandable
Test Time: 0.2 Sec
USB-Interface: 1.1 - fast
Resistance Thresholds: 46 kΩ - fixed
Resistance Measurement: no
Diode Measurement: Orientation Only
Test Voltage: 5 V
Maximum Test Current: 0.3 mA
Calibration: Not required
Test Point Connectors: 64-pin dual-row headers, 0.1” (2.54 mm) centers - two per 128-point module
Remote Control Socket: no
Probe Socket: no
Power Requirement: 9v DC at 300 ma (max), 3w, from wall module
Computer Requirements: Windows XP®/Vista®/7®/8®
KAB-TEC-192-M
The product has been discontinued by the manufacturer! We do still sell wearparts for the units in limited quantities.
Cable Test System
- with plug-in adapters -
Detecting of disconnections, electrical shorts,
diodes with wrong polarity.