Soldering & Tinning

FT-02
 

Batch Reflow Oven
- for prototyping and small series production -

  • Process temperature: max. 300° C
  • Process area: 190x290 mm
  • Warm-up time - temperature stability:
    approx. 3 min
  • Heating:
    2 x 1 kW Quartz lamp - adjustable in 2 steps
  • Display: LCD monitor
  • Microprocessor control with memory for 10 programs.
  • Homogeneous convection heater.
  • Lead-free or standard soldering profiles.
  • 16 kg / 370x455x320 mm
  • 230 V / 50 Hz - 2.2 kW

FA-400LF
 

Automativ Wave Tinning Station
- for lead-free tinning -

  • Tin capacity: approx. 7 kg
  • Temperature range: 240° C - 400° C
  • Controller: 100% solid state, plug-inserted, maintenance-friendly. Electronic tin wave level control.
  • Dimensions (LxWxH): 405x120x530 mm
  • Quick heat up time through effective heaters and only 7 kg tin content.
  • Super compact slim design.
  • Digital constant temperature pre-setting.
  • Highly corrosion-resistant tinning device.
  • Interface: optical coupler max. 35 V / 500 mA for ready signal & alarms control
  • Power supply: 230 V / 50 Hz - max. 5 A
  • Power consumption: 1.2 kW
  • Option
    - automatic flux station FX-400
    - lead-free tinning conversion kit for FA-400N

TT-31

 

We are sorry, this article doesn't belong any more to our range of products!

Flux Station
- bench-top unit -

  • Dipping depth: 1-30 mm
  • Display: dipping depth - resolution in 0.1 mm
  • Delivery height: max. 1.5 m
  • Dimensions (LxW/LxWxH)
    • Dipping area: 40x50 mm
    • Bath: 150x100x140 mm
    • Container enclosure: 380x220x550 mm
  • Container volume: 5 l
  • The flux-container and the pump are built into a stable enclosure which protects them from impact and damage. The mains switch for the pump is mounted into this enclosure and is easily accessed.
  • Stop-plate can be adjusted to any flux depth from 1 to 30 mm. Using the integrated spindle with a millimeter display, the operator can set up the flux bath for a new depth within seconds.
  • The constantly repeatable flux depth ensures a much more accurate manual tinning.
    The stop-plate increases production by more than 30 %.
  • 230 V / 50 Hz - 10 W

TT-41
 

We are sorry, this article doesn't belong any more to our range of products!

Tinning Station
- for manual dip-tinning -

  • Temperature: max. 380 ° C
  • Temperature control: PID (solid state switching)
  • Heat up time: 20 min (280° C)
  • Display: preset & actual temperature and dipping-depth
  • Tin amount: 0.181 l
  • Stop-plate depths: 0-25 mm - infinitely variable spindle position
  • Tub widths: 56 mm
  • The station is equipped with an adjustable plate which serves as a stop for an accurately repeatable tinning-length for wire-ends. This stop-plate can be adjusted to any depth up to 25 mm. Turning the integrated spindle with a millimeter display.
  • Tub for lead-free tin.
  • For the periodical tub cleaning, which is done about every two days, the stop-plate can be swiveled up and well out of the way. The whole inner tub is then easily accessed because the heating-element and the sensor are mounted on the outside.
  • Dimensions (LxWxH): 320x130x170 mm
  • Power supply: 230 V / 50 Hz (max. 1.6 A)
  • Power consumption: 200-360 W (temperature-dependant)